Convert any SATA or SATA II Hard Hard Drive to Standard USB 2.0 Port. Great For
testing Drives and Moving data between Hard Drives. A must for all Testing, Migration, and
Integration Benches. The World's First Integrated SATA to USB 2.0 Single Chip
USB + IDE + SATA Adapter for 2.5 inch 3.5 inch and 5.35 inch drives all in one Combo sata USB and IDE usb Adapter $29.98click here
2.5"/3.5"/5.25" SATA I & II to USB 2.0 cable adapter + IDE ATA-33/ATA-66/ATA-100/ATA-133 2.5", 3.5" and 5.35" UDMA IDE (PATA) Drive Adapter
The USB 2.0 to SATA Drive Adapter implements a bridge between
one USB port and one SATA or SATA II based mass storage device port. The USB 2.0 to SATA Drive
Adapter turns any standard SATA drive into a convenient external drive. Supports SATA Hard Drives from 20GB up to 2,000GB (2TB).
Easily transfer files from computer or notebook, back up files, or store large file
archives on hard drives. This is the
world's first integrated SATA to USB 2.0 single chip
solution for large capacity drives.
Converts any SATA to USB via New JMicron Chip Solution
High-Speed Data Transfer, Low Power Consumption
Supports 480 Mbps USB
Supports 1.5 GBps SATA
Small enough for travel
Red / Green LED's indicating operation
Operating System Support: Desktop and Laptop computers with Windows
98/ME/2000/2003/XP and MAC OS X.3.6 or greater
About the New JMicron Chip Solution
The JM20337 is single chip solution to bridge between USB 2.0, SATA and ATA/ATAPI-based
mass storage device. It provides the capability to translate USB 2.0 mass storage commands to serial
ATA and ATA/ATAPI communication protocol.
Compliance with Gen 1i and Gen 1m of Serial ATA II Electrical Specification 1.0
Support SATA spread-spectrum transmitter
Support SATA II Asynchronous Signal Recovery (Hot PLug) Feature
Compliance with USB 2.0 (Hi-Speed) electrical specification
Compliance with USB Mass Storage Class Bulk-Only transport specification
Support 480Mbps High Speed (HS) and 12 Mbps Full Speed USB Operation
Support ATA/ATAPI Ultra DMA Mode
Support ATA/ATAPI LBA48 bit addressing mode
Read more about this Jmicron Single Chip Solution.
Single Bit Rate:
1.5 Gbps/SATA and 480 Mbps/USB
-0.3% to 0.0
ESD Protection :
USB and SATA Products
2 Bay Storage System
Backward compatible storage system
The SATA to
USB 2.0 cable adapter comes completely packaged
with the SATA to USB 2.0 adapter converter, AC
adapter, AC power cable and Drivers on disk for
Windows 98 SE operating system.
SATA to USB 2.0 cable adapter detailed Information
The SATA to USB 2.0 Adapter is very easily connected to the SATA drive. The adapter's SATA port connection is notched for proper alignment to the SATA hard drive port. The AC power adapter as seen above is connected the the back of the SATA adapter for power to the drive for proper operation. Red and Green LED's once powered up show operation of the drive while in use. With the SATA to USB 2.0 adapter, your SATA hard drive will transfer it data via the USB 2.0 cable attached to the adapter at the USB 2.0 transfer rate of 480 Mbps, this being the limit of USB 2.0 Specs.
In working with the SATA to USB 2.0 cable adapter
converter the male to female connector was
a good tight fit when mated together. When
connected to the power supply, power up of
the hard drive was instant as the LED indicated.
The connector on the converter unit must be
aligned properly by aligning the notches in
the male connector with the female port of
the SATA hard drive before use.
Bob Boisvert...Web Professional
Serial ATA to USB 2.0 cable
adapter converter additional product images
The SATA to USB 2.0 cable adapter converter.
See a larger
Connection diagram of the Serial ATA to
USB 2.0 converter. See a larger
Serial ATA to USB 2.0 Cable
Serial ATA (SATA) or IDE 2.5" and 3.5" to USB 2.0 Cable Converter Adapter with Power Supply. The Hi-Speed USB 2.0 to Serial ATA (SATA) or IDE 2.5" and 3.5" Drive Adapter ...
SPECIAL, Now you have the IDE and SATA Adapter COMBO Unit!
SATA to USB Adapter Cable for 2.5" Hard Drives 3.5" SATA II and SATA II HDD and 5.25" Optical Drives
New SATA to USB adapter model with Hot-Plug and HOT-SWAP Reset Button.
Convert any SATA or SATA II Hard Hard Drive to Standard USB 2.0 Port. Great For testing Drives and Moving data between Hard Drives. A must for all Testing,Migration,Intergration Benches.
World's First Intergrated SATA to USB 2.0 Single Chip Solution.
-Compliant with 5.25" SATA I and SATA II DVD/Optical Drives
-USB 2.0 and 1.1 Supported
-HDD Activity LED
-Supports HOT-PLUG and Plug-AND-Play
-Bus Powered for 2.5" SATA Hard Drives
-External Power Supply:
for 3.5'' SATA Hard Drives and 5.25" DVD/Optical Drives
2.5Amp 12/5Volt DC Output Input AC 110/220 Volt Input
TECH TIP: If you are having Problems on Windows XP/2000/2003 recognizing Drive you need to Reboot your system.
-Operating System Support: Desktop and Laptop computers with Windows 98/ME/2000/2003/XP and MAC OS X.3.6 or greater